my cable box is on but my tv says no signal

If I change the channel it shows it on the box. I even got a new HDMI cable but the tv kept reading no signal Nothing seems to be working.

Why Tv Says No Signal But Cable Box Is On Easy Fix

1 min When your TV and set top box are both powered on but your TV is displaying a message that there is no signal this is an input issue with your TV.

. In Most cases pixelating pictures blocks on the screen or a No Signal message from time to. Check to see how your cable box is connected to the TV set. If your No Signal message is not due to incorrect Source or Input is selected then its most likely caused by setup or antenna fault.

YES check if the receiver is set to either ch3 or ch4 rear panel near the white sticker with barcodes. Unplug the source device from the wall outlet or power strip. Plug the MTS set-top box back in.

Remove the power cable from the back of the unit. Subsequently question is how do you fix a TV when it says no signal. Set TV to the same ch.

Power on both the TV and the X1 TV Box. For a full cable box try to use an AV input the yellowredwhite cables usually INPUT1 on many TVs. Having some trouble with your tvWe hope this video can helpIf you are a guest of ours and need any assistance please give us a call at808 329-2140.

The box is a XG2V2-S. If the problem persists. For other news regarding TV says no signal but cable box on and working and XFinity - Comcast Television see our recommended stories below.

Unplug the power cable from the back of the Bell MTS set-top box. The box is a XG2V2-S. For the past week one of my tvs has kept displaying no signal on the screen.

Estimated reading time. Spending about an hour or so on line chat with verizon to solve my 2 cable box tv problems and they lost patience with me while I swapped out the boxes to se. How to reset a newer Smart Guide digital box.

Sometimes you may notice that an HDMI cable doesnt fit well into a port it wiggles too loosely or partially falls out because one or the other has become worn. Now if the message disappears then your TV is perfectly fine but not your cable box. Reinsert pressing hard until you feel and maybe hear the click as the connector locks into place.

One of the most common reasons for a no signal message is that an HDMI cable input isnt securely fastened in the HDMI port. Power reset the source device. First check that the TV is set to the correct Source or Input.

It might be that the cables have been wrongly plugged. Ive unplugged everything and plugged it back in. Confirm that the TV is set to the proper input.

If after resetting your cable or satellite you still have the no signal message displaying on your TV then you have to check maybe there is a wrong connection somewhere. Hand-tighten all cable connections to make sure theyre not loose. Turn your digital box off.

Depending on which remote you are using you may have to press the CBL button at the top of the remote first and then the POWER button. Even after the alert signal is displayed then it is your TV. If its a little DTA box or an old SD TV and using coax then use channel 3 as mentioned.

If your TV says no signal but the cable box is on you need to reboot the cable box. The only solution seems to be unplugging the cable box and plugging it back in. Unplug each end of the HDMI cable one at a time.

UNPLUG THE CABLE GOING FROM THE TV TO YOUR CABLE OR SAT BOX-Remove the HDMI cable or other cables from your Cable TV or SAT set top box. NO check power cable on both ends. Make sure all cables connected on the set-top box and your TV are secure.

To check it remove the cable box and insert the other external device. If connected via RF-coaxial cable the TV should be on channel 3 or 4. Why does my Xfinity cable Box keep saying no signal.

The cable box seems to be working. If theres a signal the problem may be with the original input or source device. My tv is a Visio E322AR.

TV says no signal but cable box on and working is about XFinity-Comcast Television. Wait for the signal to initialize. Troubleshooting Steps Make sure all power cables are plugged into working power outlets for the TV and for your X1 TV Box.

To resolve this you simply need to switch your TVs input. Plug the HDMI cable back in. Press the POWER button on your Shaw remote control.

If nothing use the front panel buttons on the receiver. If you have another source device connected to your TV switch to that input. Ensure the TV box is powered on No Signal might just mean that the TV box is powered off.

If this doesnt solve the issue check the HDMI port for a bad connection. Wait for the signal to initialize. Wait one minute plug in the source device and then turn it on.

My tv is a Visio E322AR. If still the no signal message is displayed on the screen then you need to check your TV and the cable box. Try changing the Input or Source to AV TV Digital TV or DTV if you havent already.

What channel should my tv be on for cable. Call the cable operator to fix it. Cycle the source or input.

While the TV is powered on on the DirecTV remote control press Guide or Menu button if any screens shows up. If your digital box has power and the TV input is correct but you still have no signal on your TV screen or your digital box is displaying NO IP the digital box may be frozen and may need to be reset. How to Fix Start out by unplugging all cables from their sources and keep them unplugged for a while.

To ensure that your box is powered on. Unplug the cable box from the wall outlet for at least 60 seconds before plugging it back in.

How To Fix Your Tv When It Says No Signal The Techrim